Description
Self-powered Grade 3 outdoor siren with a sound output of 122 dB at 1 m, clear LED flash and a white polycarbonate housing with an inner galvanised steel cover.
| Sound output | 122 dB at 1 m |
|---|---|
| Security grade | Grade 3 |
| Colour | White housing, clear LED flash |
| Supply | 13.2–14.5 V DC from the panel |
| Current | 9.5–13 mA stand-by, up to 1.35 A in alarm |
| Battery | Lead-acid 12 V / 1.3 Ah (not included) |
Product description
DIONE/WH · Sigma
Self-powered Grade 3 outdoor siren with a sound output of 122 dB at 1 m, clear LED flash and a white polycarbonate housing with an inner galvanised steel cover.
The siren is triggered by the panel when a positive or negative voltage is removed: the +TRIGGER input is balanced by a steady 8–12 V DC and alarms when that voltage is cut or drops below 5.0 V DC; the −TRIGGER input is balanced while it is connected to the panel negative. Only one of the two inputs is used. It follows the panel's alarm time, but also sounds if the wires are cut or short-circuited: 5 minutes if the +12 V supply is cut, 15 minutes if only the TRIGGER wire is cut. Each alarm starts at low volume for 10 seconds (pre-alarm / test mode) before rising to full level.
The flash has two high-brightness LEDs that blink alternately in stand-by and keep flashing for 15 minutes after the alarm ends, so the location is easy to find. The SIGN input shows arming and disarming for as long as it receives +12 V, with the flash only from the factory, or with flash and sound if JP2 is cut. The FLT OUT output (open collector) switches when the battery falls below 11.0 V, is disconnected or is faulty, and connects to an LED or a panel zone.
It takes a 12 V / 1.3 Ah lead-acid battery, not included. Charging stops above 13.8 V, the battery is protected against short circuit and reverse polarity, and without supply from the panel the siren will not sound with the battery below 10.0 V, so the battery is not damaged. Installation can be finished before the panel is connected: the siren starts working the first time the panel supplies voltage. Tamper on cover and wall, built-in spirit level on the base and IP44 protection.
| 1 | Trigger by voltage removal. +TRIGGER or −TRIGGER input, with an alarm also when the wires are cut or shorted. |
|---|---|
| 2 | Pre-alarm / test mode. Low volume for the first 10 seconds of each alarm. |
| 3 | LED flash. Blinks in stand-by and for 15 minutes after the alarm. |
| 4 | SIGN input. Arm / disarm indication with flash, or flash and sound (JP2). |
| 5 | FLT OUT output. Signal for low, disconnected or faulty battery. |
| 6 | Double tamper. Volt-free contacts for cover opening and wall removal, to a 24-hour zone. |
Technical specifications
DIONE/WH
| SOUND AND FLASH | |
|---|---|
| Sound output | 122 dB at 1 m |
| Operating frequency | 900–2,700 Hz |
| Maximum alarm time | 15 minutes |
| Flash | 2 high-brightness LEDs |
| Security grade | Grade 3 |
| INPUTS AND OUTPUTS | |
| +TRIGGER | Balanced by 8–12 V DC, alarm when cut or below 5.0 V DC |
| −TRIGGER | Balanced while connected to panel −, alarm when disconnected |
| SIGN | Arm / disarm indication on +12 V |
| FLT OUT | Open collector, below 11.0 V or battery disconnected / faulty, resets above 11.5 V |
| Cut wires | 5 minutes (supply or all), 15 minutes (TRIGGER only) |
| Tamper | Cover and wall, NC-NO 600 mA / 125 V DC |
| POWER | |
| Supply voltage | 13.2–14.5 V DC |
| Operating voltage | 13.8 V DC |
| Stand-by current | 13.0 mA with LEDs lit, 9.5 mA with LEDs off, 8 mA on battery only before first power-up |
| Alarm current | 1.2 A sound only, 1.35 A with flash |
| LED flash current | Up to 150 mA |
| Battery | Lead-acid 12 V / 1.3 Ah (not included) |
| Battery protection | Charging stops above 13.8 V, short circuit, reverse polarity |
| Connection cable | 2 × 0.50 + 4 × 0.22 mm² |
| MECHANICAL | |
| Housing | Polycarbonate, inner galvanised steel cover |
| Housing colour | White |
| Flash colour | Clear |
| Ingress protection | IP44 |
| Dimensions | 190 × 290 × 65 mm (W × H × D) |
| Weight | 1,280 g (without battery) |
| Manufacturer code | 5041027 |
Documents
4 PDF files · English and Greek
| Type | TITLE | LANGUAGE | FORMAT | Open |
|---|---|---|---|---|
| BrochureDIONE-WH - Brochure EN.pdf | English | PDF · 1.0 MB | Download the file Brochure | |
| Certificate Grade 3DIONE-WH - Certificate Grade 3.pdf | — | PDF · 1.5 MB | Download the file Certificate Grade 3 | |
| ManualDIONE-WH - Manual GR.pdf | Greek | PDF · 0.1 MB | Download the file Manual | |
| BrochureDIONE-WH - Brochure GR.pdf | Greek | PDF · 1.1 MB | Download the file Brochure |