CM751 – Ethernet module

Description

Product description

CM751 · Digiflex

Plug-on Ethernet module for the Vision-X, Vision-XIP and MyAlarm-XIP panels: IP reporting to an alarm receiving centre (ARC), MyAlarm Cloud connection and VisionLink programming, locally or remotely.

The CM751 plugs onto the control panel's expansion port header on three plastic standoffs and connects to the building's local network with a CAT 5E cable. It is powered by the panel and takes 60 mA from the 12 V accessory power available. The panel supervises the module continuously and reports a trouble when communication with it is lost.

It sends alarm signals to the ARC over IP in SIA IP, CSV IP or MyAlarm IP, using little bandwidth. The link is supervised by poll messages at an interval you set, and data can be encrypted with 128-bit AES. You can set the Ethernet path for reporting destination 1, 2 or both. It also connects the system to MyAlarm Cloud.

With the VisionLink software you upload and download programming, review the event history and operate outputs and areas, on the local network or remotely over the internet, using TCP (default) or UDP. Remote access needs port forwarding on the router (default port 7701); where the public IP address changes, the panel is found through MyAlarm Cloud by the module's MAC address. Seven LEDs on the board show the module's status and network activity.

STANDARD FUNCTIONS
1Plug-on. Fits directly on the panel's expansion port, with no bus wiring.
2ARC reporting. Over IP: SIA IP, CSV IP and MyAlarm IP, with link supervision (polling).
3Encryption. 128-bit AES on the transmission to the ARC.
4MyAlarm Cloud. Connects the system to the MyAlarm service.
5VisionLink over IP. Programming, event history and control of outputs and areas, locally or remotely.
6IP address. Static or by DHCP; a static or reserved address on the router is recommended.

Technical specifications

CM751

COMMUNICATION
Network interfaceEthernet RJ45, 10BASE-T / 100BASE-TX, auto sensing
ARC reportingOver IP: SIA IP, CSV IP, MyAlarm IP; also Conettix / Conettix NNC
Reporting destinationsEthernet on destination 1, 2 or both
Link supervisionPoll messages at an interval you set (default 30 s)
Encryption128-bit AES (Rijndael)
BandwidthLow usage
Network protocolsUDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, SMTP, HTTP
IP addressStatic or by DHCP
REMOTE ACCESS
CloudMyAlarm Cloud
ProgrammingVisionLink over IP, local or remote
Connection protocolTCP (default) or UDP
VisionLink port7701 (default)
Dynamic public IPPanel located through MyAlarm Cloud by MAC address
Access restrictionCan accept connections from one IP address only
INDICATORS
Board LEDsSTATUS, RX, TX, POLL, REPORT
RJ45 socket LEDsLink / data activity and full / half duplex
POWER AND INSTALLATION
Supply12 V from the panel
Current60 mA
MountingPlug-on to the panel's expansion port, on 3 plastic standoffs
Compatible panelsVision-X (firmware V2.10 or later), Vision-XIP, MyAlarm-XIP
SoftwareVisionLink V2.01 or later
Package contentsCM751 module, 3 plastic standoffs, HW750 riser kit (for use with the CM101 voice module)
MECHANICAL
Dimensions93 × 52 × 30 mm
Operating temperature0 to +55 °C
Operating humidity5–85% at 30 °C, non-condensing

Documents

3 PDF files · English and Greek

TypeTITLELANGUAGEFORMATOpen
PDFInstallation manualCM751 - Installation manual EN.pdfEnglishPDF · 3.8 MBDownload the file Installation manual
PDFDatasheetCM751 - Datasheet EN.pdfEnglishPDF · 2.6 MBDownload the file Datasheet
PDFNetwork setup guideCM751 - Network setup guide GR.pdfGreekPDF · 0.9 MBDownload the file Network setup guide